How to Draw Porch Railing in Autocad Architecture
Drawing the Deck Posts Autocad
There are four posts on the deck: two 8″ (204 mm) posts at the corners that
hold up the roof, and two 4″ (102 mm) posts at the top of the stairs. You will use the Rectangle (RECTANG) command to draw the posts and the MIRROR command to copy them:
1. Make sure I05-03-FrontDeck.dwg (M05-03-FrontDeck.dwg) is open
2. Use the Rectangle (RECTANG) command, found on the Home tab ➢
Draw panel ➢ Rectangle tool, to draw a post 8″ × 8″ at the lowerright
corner of the deck.
To do this, start the Rectangle (RECTANG) command. At the Specify
first corner point or: prompt, click the endpoints where the
lines form the lower-right corner of the deck. At the Specify other
corner point or: prompt, enter -8,8↵ (-204,204↵) to draw the
first 8″ (204 mm) post.
The rectangle should be similar to Figure 5.15.
F igu re 5 . 1 5 : The first corner post
3. To create the opposite post, select the rectangle that you just drew
and then start the MIRROR command (Home tab ➢ Modify panel ➢
Mirror tool).
4. At the Specify first point of mirror line: prompt, use the
Midpoint Object Snap. Then pause the cursor over either of the vertical
handrail lines.
When a feature is symmetrical like the deck, you can use the
Midpoint snap to mirror objects about the centerline.
5. Move the cursor directly to the left or right, as shown in Figure 5.16,
to mirror the post. Then do the following:
F igu re 5 . 1 6 : The first deck posts are in place.
a. Click to execute the mirror.
b. Press ↵ to accept the No option for deleting the source object.
6. Use the TRIM command to trim the short polyline segments that fall
within the posts.
When you are finished, each segment should look similar to
Figure 5.17.
F igu re 5 . 1 7 : Trim the handrail lines to clean up the post.
7. Save your drawing as I05-04-DeckPosts.dwg (M05-04-DeckPosts.dwg).
The 4″ (102 mm) posts at the top of the stairs are centered on the 3″ (72 mm)
handrails on the deck and on the stairs. To create the lower small post, you
need to locate the bottom-right corner at a point 1⁄2″ (15 mm) to the right of
the front handrail and 5′-8 1⁄2″ (1740 mm) from the bottom-right corner of the
deck. Follow these steps:
1. Make sure I05-04-DeckPosts.dwg (M05-04-DeckPosts.dwg) is open.
2. Select the large lower post and start the COPY command from the
Home tab ➢ Modify panel on the Ribbon.
3. Select the lower-right corner point as the base point and then, at the
Specify second point or: prompt, enter .5,5′8.5″ (15,1740
4. Press ↵ to end the COPY command. The copied post appears as shown
in Figure 5.18.
F igu re 5 . 1 8 : The copied deck post
5. Zoom in to the new post. The bottom-right corner of the post is
located in the correct location, but the post is twice the size that it
should be.
6. Start the SCALE command by clicking the Scale button from the
Home tab ➢ Modify panel; then select the new rectangle.
7. With the SCALE command active, select the lower-right corner as the
base point. Then move the cursor to see the effect when the scale
is based from that corner. A copy of the selected object appears, as
shown in Figure 5.19.
F igu re 5 . 1 9 : A copy of the scaled object appears as you move the cursor.
8. Enter 0.5↵ to scale the rectangle to 50 percent of its current size.
9. Save your drawing as I05-05-StairPosts.dwg (M05-05-
StairPosts.dwg).
Incoming search terms:
- DECKED WINDOWS ON AUTOCAD
Tags Autocad 2012 command Autocad 2012 doc Autocad 2012 document Autocad 2012 ebook Autocad 2012 engineering Autocad 2012 help Autocad 2012 interface Autocad 2012 learning Autocad 2012 material Autocad 2012 menu Autocad 2012 pdf Autocad 2012 selection Autocad 2012 solution Autocad 2012 tips Autocad 2012 toolbars Autocad 2012 training Autocad 2012 tricks Autocad 2012 tutorial Autocad 2012 video how to Autocad 2012
Source: https://cadcamengineering.net/drawing-the-deck-posts-autocad/
0 Response to "How to Draw Porch Railing in Autocad Architecture"
Post a Comment